User Tools
start:first_simulation
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision | Next revision Both sides next revision | ||
|
start:first_simulation [2018/09/04 15:08] pgrolich |
start:first_simulation [2018/09/04 15:20] pgrolich |
||
|---|---|---|---|
| Line 5: | Line 5: | ||
| ===== Summary ===== | ===== Summary ===== | ||
| - | We will use cubic volume with centered point source, similar to a dipole located in center of computation space. | + | We will use cubic volume with centered point source, similar to a dipole located in center of computation space. Outputs will be different cross-section planes to Gwyddion file and a text file (from single point). |
| - | Outputs will be different cross-section planes to Gwyddion file and a text file (from single point). | + | |
| Calculation will be performed on CPU or on GPU and material mode selection for speedup will be tested. | Calculation will be performed on CPU or on GPU and material mode selection for speedup will be tested. | ||
| Line 24: | Line 23: | ||
| you will be able to use GUI only for parameter file setup. | you will be able to use GUI only for parameter file setup. | ||
| - | When you start XSvit, there is already a default parameter file loaded, using computational space of size 100x100x100 voxels. We will use this computational space and we will add point souce and point output. In the next figure you can see how the default settings look after XSvit start (you can rotate the 3D projection by mouse, so this was done to get a better view). Note the values of discretisation step (10 nm) in the list of all the entries on the left side of the window; if we work in vacuum (which is the case in this example) we should not use source with wavelength that is smaller than this step multiplied by ten. You can alter the discretisation settings and computational volume size by double clicking on its values in the list. | + | When you start XSvit, there is already a default parameter file loaded, using computational space of size 100x100x100 voxels. We will use this computational space and we will add **point souce** and **point output**. Save default parameter file to **first-simulation.par** file using menu entry //File->Save//. In the next figure you can see how the default settings look after XSvit start (you can rotate the 3D projection by mouse, so this was done to get a better view). Note the values of discretisation step (10 nm) in the list of all the entries on the left side of the window; if we work in vacuum (which is the case in this example) we should not use source with wavelength that is smaller than this step multiplied by ten. You can alter the discretisation settings and computational volume size by double clicking on its values in the list. |
| {{:start:screenshots:first-simulation-init.png?400|}} | {{:start:screenshots:first-simulation-init.png?400|}} | ||
| - | It is reasonable to save your parameter file at this stage using <i>File->Save</i> command. We can do it also later, just before running computation, however doing it right now will set the current directory and other input/output files | + | It is reasonable to save your parameter file at this stage using <i>File->Save</i> command. We can do it also later, just before running computation, however doing it right now will set the current directory and other input/output files set later can be referred to it (instead of using absolute path). Moreover, by saving parameter file we also set default directory for temporary files (e.g. generated sources), which is also important. |
| - | set later can be referred to it (instead of using absolute path). Moreover, by saving parameter file we also set default directory | + | |
| - | for temporary files (e.g. generated sources), which is also important. | + | |
| First we will add **point source**. This can be done using menu entry //Edit parameters->Add point source//. | First we will add **point source**. This can be done using menu entry //Edit parameters->Add point source//. | ||
| Line 45: | Line 42: | ||
| Next we will add <b>point and image outputs</b>. This is done by menu entry //Edit parameters->Add point output// and //Edit parameters->Add image output// that again open dialogues for specifying how often (parameter "skip") and which component should be output. Point output is collected from a single point within computational volume and is stored into a text file. Image output comes to general output file that can be opened by [[http://gwyddion.net|Gwyddion]] open source software. A cross section in certain normal direction is output, selected as shown below. We will add a cross section in every direction, so we will call the dialog three times. | Next we will add <b>point and image outputs</b>. This is done by menu entry //Edit parameters->Add point output// and //Edit parameters->Add image output// that again open dialogues for specifying how often (parameter "skip") and which component should be output. Point output is collected from a single point within computational volume and is stored into a text file. Image output comes to general output file that can be opened by [[http://gwyddion.net|Gwyddion]] open source software. A cross section in certain normal direction is output, selected as shown below. We will add a cross section in every direction, so we will call the dialog three times. | ||
| - | <img src="http://gsvit.net/images_v18/ex1_imout.png"> | ||
| - | <p>Similarily we will add point output as shown below.</p> | + | {{:start:first-simulation-image-output.png?400|}} |
| + | |||
| + | Similarily we will add point output as shown below. | ||
| <img src="http://gsvit.net/images_v18/ex1_pout.png"> | <img src="http://gsvit.net/images_v18/ex1_pout.png"> | ||
start/first_simulation.txt · Last modified: 2019/01/14 07:58 by pgrolich
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial 4.0 International
